DD-WRT is likely to be many a term, this ingenious router operating system provides endless configuration options for wireless router. I have a Linksys WAP54G and a TP-Link TL-WR1043ND flashed with DD-WRT, which are currently in operation and diligently perform their duties.
Only good, then bad
Especially after the flash of the TL-WR1043ND I was very impressed by the performance that unfolds the router. So I also have my TL-WR941ND 3.0 flashed with DD-WRT. As you can see in the screenshot below, there was only the preSP2 v24 [Beta] 15778 available, but not stable.
After DD-WRT was configured, the router ran about 1.5 weeks until the WLAN failed. While the WLAN LED lit, but there was no Wi-Fi network available. I thought nothing of it and started the router just new, it ran again. A week later the incident repeated again and I was skeptical. At first I thought that it is on the channel, and changed from 3 to 11 At first it went well, but then came the third wireless crash. This story repeated itself again and again, almost regularly. Until I came up with the idea that it could be due to DD-WRT. After a google session it was clear that the TL-WR941ND has problems with the WLAN if DD-WRT is installed. I think the beta is for verwantwortlich. Although I have the TL-WR1043ND flashed with a beta, but that was the 14896 build.
Back to Stock Firmware
Now a flash was on the floor firmware of TP-Link. Unfortunately you can not simply transfer as the BIN file using the DD-WRT web interface, you get an error. After much searching, I had found several methods that should enable the Revert, such as telnet or tftp in conjunction with Ping etc. But all this did not help me further, or was so complicated that I would have needed a lot of time.
Suddenly I came across a thread in the DD-WRT forum, by special firmware files are available for download, which can be loaded directly to the web interface of DD-WRT ("Webrevert"). The offered file for the TL-WR941ND was spot on and brought my router in 5 minutes back to the original state, without further ado with Telnet, SSH, or TFTP.
Downloads
For those who are not registered to the forum, there is the possibility to load the files directly.
TP-Link TL-WA801N/ND v1 Webrevert download here
TP-Link TL-WA901N/ND v1 Webrevert download here
TP-Link TL-WA901N/ND v2 Webrevert download here
TP-Link TL-WR740N v1/v2 Webrevert download here
TP-Link TL-WR740N v3 Webrevert (world wide version only) download here
TP-Link TL-WR741N/ND v1/v2 Webrevert download here
TP-Link TL-WR743N/ND v1 Webrevert download here
TP-Link TL-WR841N/ND v3 Webrevert download here
TP-Link TL-WR841N/ND v5 Webrevert download here
TP-Link TL-WR841N/ND v7 Webrevert download here
TP-Link TL-WR941N/ND v2/v3 Webrevert download here
TP-Link TL-WR941N/ND v4 Webrevert download here
TP-Link TL-WR1043ND v1 Webrevert download here
3 comments:
I am running a wireless broadband service.and we r using TP-Link CPE 543G and 500G.and also binatone(Gargoyal).but I only access net in 500G.but 543G singnal the quality is too poor.and binatone shows signal more than 70% but cant access internet..can I load the TL 500G firmware in both the CPE 543G and binatone?
@mark :
If you want to Bond to broadband you can use conectify by using any PC, if you want embeded PC like wireless router you can reflashed with Tomato.
Looking for Tp-link Australia call on 1800987893 , visit on: Tp-link Australia
Post a Comment