Huawei BM622i Change MAC via Upgrade Telnet

Here's another trick to change the MAC Address of your Huawei BM622i 4G WiMAX CPE wireless broadband modem using BM622i V100R001PHLC08B029PST03.exe dis-upgrading the firmware 2011 via telnet command line interface (cli).

First you have to download here the Globe WiMAX 4G wireless broadband CPE modem upgrade utility filename for Huawei BM622i V100R001PHLC08B029PST03.EXE and run it, as you can see the screenshot above.

Just leave it open as it on the screenshot above, open up telnet client if you have Putty utility much better input 192.168.254.1 at port 23 and click open.. But if you don't have on your Windows 7 you must enable it on Control Panel  then Program and Features where telnet is located. Windows XP telnet client is enable by default just Click Start => Run then type telnet 192.168.254.1 command hit enter it will prompt you a window lead to command line interface.

You may now login using the simple steps below:

LOGIN: Firefly

PASSWORD: $P4mb1h1r4N4m4nT0!!

Then press enter

ATP>xiugai macdizhi XX:XX:XX:XX:XX:XX
ATP>diag restore default

Wait, now the Huawei BM622i WiMAX 4G Wireless broadband CPE modem will reboot. Open any your favorite browser on address bar type http://192.168.254.1 with the username and password user, use Huawei WiMAX password generator to generate the admin password to be able to login as admin privilege account.

Congratulation, you may now able to change your Huawei BM622i WiMAX 4G CPE wireless broadband modem.

Read More

BM622i Change MAC via Telnet 2011 Firmware

This tutorial is how to change MAC Address on Huawei BM622i WiMAX CPE 4G wireless broadband modem firmware 2011 aka V100R001PHLC08B025. To do this is you must have a telnet client, if you are using Windows 7 you must enable it first on your Control Panel => Programs and features. On Windows XP telnet client is enable by default or you can use Putty if you do not have one it is also a telnet client.

If your prefer to used Windows telnet client  you can click Start => Run, then type cmd a command to open Windows command line interface (CLI) then just press enter will prompt you a window. Type telnet 192.168.254.1 be sure your in the same subnet IP address range. On the other hand, you can also use Putty utility a graphical interface (GUI) telnet client just input 192.168.254.1 on port 23 and it will open a window telnet.

Here's the few steps on how to do the stuff via telnet command line interface:

—————————————
——–Welcome to ATP Cli——
—————————————
Login: wimax
Password:wimax820
ATP>diag set macaddr XX:XX:XX:XX:XX:XX

set Lan mac address success
Lan mac address updated XX:XX:XX:XX:XX:XX
set Lan Mac address Sucess
Wan mac address updated XX:XX:XX:XX:XX:XX

ATP>diag reboot

Wait, Huawei BM622i will reboot.

Then after the Huawei BM622i WiMAX CPE 4G broadband modem reboots, open any browser type http://192.168.254.1 login with the Username and Password "user", used password generator to generate an admin password for the MAC you used and log in as admin on Huawei BM22i.

On the left side menu clicked or go to WiMAX => Security
You must change the NAI with your MAC Address "XXXXXXXXXXXX@globelines.com.ph"

Changing the Username and Password is a must with the admin password you have generated from your generator and then click apply to save the changes. If it works for me then absolutely it will also works for you.

Congratulation and enjoy!

Read More

Huawei BM622 downgrade firmware 2010 via tftp

First of all is we have to make it sure that we are able to access or connect the Huawei BM622  4G WiMAX wireless broadband modem CPE by verifying through pinging the IP address 192.168.1.1 via CLI (command line interface) or thru web GUI (graphical user interface) on browser with same IP address at http://192.168.1.1 to make it realistic as show below snap shot.

Whether or not the Huawei BM622  4G WiMAX wireless broadband modem CPE enable/disable its DHCP server we have also to verify our PC if we are using Dynamic or Static IP address to anticipate if the CPE device reboots failed to provide IP address or the PC itself can not acquire its IP address.

Static IP address is more preferable during TFTP firmware uploading operation to make it sure we are in the same IP address subnet and our PC is still connected even if the CPE device fail its DHCP server during power on.

To start with, the PC must be ON with the Static IP address above mention. Power off the CPE device Huawei BM622, unplug the AC/DC adapter then plug it again and remain the power is OFF.

1. Click START and RUN, then type cmd to open windows CLI (command line interface) mode
2. Type cd\ to change directory i.g. C:\
3. Make sure your bm622firmware2010.bin is in local drive C:\
4. Type tftp –i 192.168.1.1 put bm622firmware2010.bin as you can see from the screenshot below, wait DO NOT press enter yet until to do so.

5. Make sure or double check that the LAN cable is physically connected to the PC and to the CPE device Huawei BM622 port.
6. Using a pin or sharp item insert onto the pin hole and press the “Reset” button at the side of the CPE device Huawei BM622 as shown below snapshot.

7. Press the Power ON button of the Huawei BM622 while still pressing the "Reset" button.
8. Release the “Reset” button of the Huawei BM622 and press Enter to begin the TFTP firmware downgrade/upgrade.
9. Please wait for 1 (one) minute and reboot the modem.
10. Press “Reset” while BM622 is ON.
11. Open your browser type http://192.168.1.1 to verify or check if your firmware is already being uploaded, just do same procedure if it is unsuccessful. This tutorial is if you want to downgrade or upgrade your BM622 firmware via TFTP, this can be also applied to 4G WiMAX CPE Huawei model BM621, BM622i, BM625, and BM626.

Read More

Huawei BM622 TFTP Firmware Upload

First of all is we have to make it sure that we are able to access or connect the Huawei BM622  4G WiMAX wireless broadband modem CPE by verifying through pinging the IP address 192.168.1.1 via CLI (command line interface) or thru web GUI (graphical user interface) on browser with same IP address at http://192.168.1.1 to make it realistic as show below snap shot.

Whether or not the Huawei BM622  4G WiMAX wireless broadband modem CPE enable/disable its DHCP server we have also to verify our PC if we are using Dynamic or Static IP address to anticipate if the CPE device reboots failed to provide IP address or the PC itself can not acquire its IP address.

Static IP address is more preferable during TFTP firmware uploading operation to make it sure we are in the same IP address subnet and our PC is still connected even if the CPE device fail its DHCP server during power on.

To start with, the PC must be ON with the Static IP address above mention. Power off the CPE device Huawei BM622, unplug the AC/DC adapter then plug it again and remain the power is OFF.

1. Click START and RUN, then type cmd to open windows CLI (command line interface) mode
2. Type cd\ to change directory i.g. C:\
3. Make sure your bm622firmware2010.bin is in local drive C:\
4. Type tftp –i 192.168.1.1 put bm622firmware.bin as you can see from the screenshot below, wait DO NOT press enter yet until to do so.

5. Make sure or double check that the  LAN cable is physically connected to the PC and to the CPE device Huawei BM622 port.
6. Using a pin or sharp item insert onto the pin hole and press the “Reset” button at the side of the CPE device Huawei BM622 as shown below snapshot.

7. Press the Power ON button of the Huawei BM622 while still pressing the "Reset" button.
8. Release the “Reset” button of the Huawei BM622 and press Enter to begin the TFTP firmware upload.
9. Please wait for 1 (one) minute and reboot the modem.
10. Press “Reset” while BM622 is ON.
11. Open your browser type http://192.168.1.1 to verify or check if your firmware is already being uploaded, just do same procedure if it is unsuccessful. This tutorial is if you want to downgrade or upgrade your BM622 firmware via TFTP, this can be also applied to 4G WiMAX CPE Huawei model BM621, BM622i, BM625, and BM626.

Read More

Huawei BM622 TFTP Firmware Download

First of all is we have to make it sure that we are able to access or connect the Huawei BM622  4G WiMAX wireless broadband modem CPE by verifying through pinging the IP address 192.168.1.1 via CLI (command line interface) or thru web GUI (graphical user interface) on browser with same IP address at http://192.168.1.1 to make it realistic as show below snap shot.

Whether or not the Huawei BM622  4G WiMAX wireless broadband modem CPE enable/disable its DHCP server we have also to verify our PC if we are using Dynamic or Static IP address to anticipate if the CPE device reboots failed to provide IP address or the PC itself can not acquire its IP address.

Static IP address is more preferable during TFTP firmware backup or downloading operation to make it sure we are in the same IP address subnet and our PC is still connected even if the CPE device fail its DHCP server during power on.

To start with, the PC must be ON with the Static IP address above mention. Power off the CPE device Huawei BM622, unplug the AC/DC adapter then plug it again and remain the power is OFF.

1. Click START and RUN, then type cmd to open windows CLI (command line interface) mode
2. Type cd\ to change directory i.g. C:\
3. Type tftp –i 192.168.1.1 get bm622firmware.bin as you can see from the screenshot below, wait DO NOT press enter yet until to do so.

4. Make sure or double check that the  LAN cable is physically connected to the PC and to the CPE device Huawei BM622 port.
5. Using a pin or sharp item insert onto the pin hole and press the “Reset” button at the side of the CPE device Huawei BM622 as shown below snapshot.

6. Press the Power ON button of the Huawei BM622 while still pressing the "Reset" button.
7. Release the “Reset” button of the Huawei BM622 and press Enter to begin the TFTP firmware download.
8. Please wait for 1 (one) minute and reboot the modem.
9. Press “Reset” while bm622 is ON.
10. Open your MyComputer  local drive C:\ and check if bm622firmware.bin is already being copied.

Read More

Huawei BM622 Blank WAN Substitute

If you happen accidentally, burned the WAN IC of your Huawei BM622 while removing the chips  from the board due to over heating of your workstation Hot-Air blower or brick it. Worry no more because the Huawei BM622 WAN IC Serial Flash Memory ST Micro/SGS M25P32 or the Spansion S25FL032A has so many cross references or substitute with other electronics manufacturer.

Here are few cross references or substitute to WAN IC of Huawei BM622 Serial Flash Memory ST Micro/SGS M25P32 or the Spansion S25FL032A.

Atmel	Intel	Macronix	SST	ST Microelectronic	Winbond
AT26DF321       datasheet	QB25F032S33B8	MX25L3205 datasheet	SST25VF032 datasheet	M25P32 datasheet	W25X32 datasheet
			SST26VF032 datasheet

You can use this programming tool SPI-FlashROM-Programmer-r1.6.7 to be able to dump, read and write the chips.

Read More

How To Remove Spansion S29GL064 From BM622

Before doing this you MUST be a good experienced technician otherwise you will damage the Spansion S29GL064 flash memory IC and the board of the Huawei BM622 wireless broadband CPE modem.

Obviously, you have to open it! First you have to turn off or unplug the power and the cables from the device itself. Removed all four screws by using a match screw driver.

This is the board of the Huawei BM622 wireless broadband WiMAX CPE modem, the red mark represent the Spansion S29GL064 IC where the flash memory chip is. Other version of Huawei model BM622 its ST Micro M29W640 instead of Spansion flash memory this is just same TSOP48.

To be able to successfully removed this chip you must have a Gordak or in short a workstation  "Hot-Air" blower, these equipment are cellphone technician best friend without this stuff they can not finish their job in repairing mobile phone.

Before you can start the heating stage of the flash memory Spansion S29GL064 make it sure the Hot-Air is already stable, meaning the heat and the air must be blend that is why you must be a good experienced technician so that you know how to matched the required level of heat and the air to eliminate the damage of the board especially the flash memory chip Spansion S29GL064 or ST Micro M29W640 for other version.

Another thing to remember to avoid burning the flash memory chip Spansion S29GL064 or ST Micro M29W640 before pointing the nozzle head of the Hot-Air blower to the chips while on stable required heat and air make sure TOO MUCH flux is already being applied on it.

It will not take long to heat the flash memory chip Spansion S29GL064 or ST Micro M29W640 you will be able to remove it by lifting it using a small flat blade. Never use tweezer on removing or lifting the flash memory this will result a broken pins of the chips while pulling it.

Read More

Huawei BM622 Blank WAN Solved!

Huawei BM622 model is the first 4G WiMAX CPE wireless broadband modem supplied by Huawei Technologies from Shenzhen's for Globe Telecom one of the major wireless broadband ISP in the Philippines. 

Recently there were so many complains from the 4G WiMAX wireless broadband subscribers that their CPE modem can't access to the internet. They have noticed upon opening the web GUI of the said 4G WiMAX CPE modem Huawe BM622 on the part of WAN interface its MAC address is missing/blank no wonder their connection interrupted or unsuccessful. 

Until now there is still an issue of so called "BLANK WAN" of Huawei BM622 4G WiMAX wireless broadband CPE, to solved this problem and issue one should knows in basic electronics skill. BLANK WAN in other words WAN chips the ST Micro/SGS M25P32 Serial flash Memory IC is corrupted this is due to malicious programming or setting done by user in wrongly manipulations.

These are the things what you need to be able to solved your Huawei BM622 BLANK WAN.

1. 50pesos LPT SPI hardware programmer or USB SPI hardware programmer (DIY)
2. TV/DVD SPI Flash programmer software (Download)
3. ST Micro/SGS M25P32 Serial flash Memory dump binary (ask Google/Forum/Neighbor/Friend)

The procedure to solve the BLANK WAN, first buy or do it yourself LPT SPI hardware programmer. Second is to download TV/DVD SPI flash programmer, third search and download BM622 WAN dump file from Google, forum, or download via TFTP your neighbor/friend BM622 ST Micro/SGS M25P32 Serial flash Memory dump binaries to your local drive.

If you have all these stuff now you can removed your Huawei BM622 WAN chips ST Micro/SGS M25P32 Serial flash Memory IC from its board and start uploading via LPT SPI hardware programmer or USB SPI hardware programmer using the TV/DVD SPI Flash programmer software.

Lastly, of course you have to put back your ST Micro/SGS M25P32 Serial flash Memory IC to its place again. If you are tired of placing it to its original position you can just soldered using 1ft/12 inches tiny wires for simplicity.

Read More

Huawe BM622i works without Spansion

Who knows that Globe Telecom WiMAX CPE wireless broadband modem Huawei model BM622i that it will still works without the Spansion 25FL128 or the ST Micro 25P128 chips? These snap shot below is taken from Symbianize forum credit to d_Bug showing that the said WiMAX CPE Huawei BM622i is on operation after pulling the chips (S25FL128 or M25P128) works fine smoothly and normal in condition.

Yes, as you can see from the screenshot above the Globe WiMAX CPE wireless modem Huawei model BM622i works perfectly after pulling the Spansion chips S25FL128.

Read More

Huawei BM622i Firmware Destroyer HW Protector

This is the latest automatic hardware protection all protected firmware and wan chips when protection is "on". Credit ko to kay boss lavaboy sa mga idea na binigay at design niya salamat bossing. nagpapasalamat din ako sa kasama kong technician na si tools1180 sa pagtulong nya sakin sa paggawa ng circuit design...

LED indicator:

1 Red = unprotected firmware & wan
1 Green = protected firmware & wan read-only mode (lan & wan cannot be change)

Switches :

1 rocker switch = on & off
1 push botton = to change wan & lan mac unprotected.

Relay and some parts.

Adapter is plug in modem off

Modem turn on

Modem protected

The modem is boot-up completed and operates with protected mode...Firmware chip is in read-only mode (no configuration setting can be changed); wan chip is in read-only mode (no wan/wimax signal settings can be changed... Wan mac cannot be changed even by the user)

This article can be found at Symbianize Forum created by soundbass1967

Read More

MTX USB SPI NAND Flasher Programmer

Matrix 360 NAND Programmer MTX USB SPI Flasher V1.0 For XBOX360 Game Module

Specification:

• Matrix NAND Programmer MTX SPI Flasher V1.0 For XBOX360
• Cost effective NAND reader / programmer to complete the GliGli Hack.
• It features a PIC18F2455 microcontroller for stable and quick reading/writing of all NAND models available on the different XBOX360 models.
• The Matrix NAND programmer is also fully compatible with NANDPRO 2.0e and several other third party programming tools.

Features:

• Fast USB SPI 360 NAND programmer.
• Fully compatible with all XBOX360 NAND models.
• Fully compatible with NandPro2.0e Software and other third party software.
• Easily reprogrammable with via USB connector.
• Quick reading and writing times.
• Microchip based for enhanced stability

Read More

Cheap SPI Flash Programmer

The circuit is connected to the PC via parallel port and he have external power supply.

This programmer supports: ST Micro M25(E), ST Micro M45(E), Macronix MX25L, Atmel AT25FS, Atmel AT25DF, Atmel AT25F, Amic A25LxxP, Amic A25Lxxx, Eon EN25(B/D/F/P) read only, Winbond W25X, Winbond W25Q (OTP), SST SST25(LV/VF)xx, SST SST25VFxxxB, Spansion S25FL and ESMT F25L.

Read More