PLDT Fiberhome ONU RP2684

As per request one of my commentator on this blog, a legit PLDTHOMEFIBR subscriber commented that his AN5506-04-F ONU/ONT just get recently patched with firmware RP2684 and nowhere to find the password for adminpldt account.

Yes there is few changes of  this firmware RP2684 of Fiberhome ONU AN5506-04-F one of those is the prevention from gaining the adminpldt access level to do the configurations on the web user interface so PLDT can limit the subscribers from doing so to the said FTTH device.

Here a list of the command line interface that you can do or practice. Take note that any alteration done by you or by your behalf will void the warranty of your PLDT Fiberhome ONT/ONU device when malfunction occur.

WRI(DEBUG_H)> list
0. active section [0|1]
1. bobtest read_regs slave_addr <0-255> begin_addr <0-255> count <1-32>
2. bobtest write_regs slave_addr <0-255> begin_addr <0-255> count <1-32> value1 <0-255> {value2 <0-255>}*1 {value3 <0-255>}*1 {value4 <0-255>}*1 {value5 <0-255>}*1 {value6 <0-255>}*1 {value7 <0-255>}*1 {value8 <0-255>}*1 {value9 <0-255>}*1 {value10 <0-255>}*1 {value11 <0-255>}*1 {value12 <0-255>}*1 {value13 <0-255>}*1 {value14 <0-255>}*1 {value15 <0-255>}*1 {value16 <0-255>}*1 {value17 <0-255>}*1 {value18 <0-255>}*1 {value19 <0-255>}*1 {value20 <0-255>}*1 {value21 <0-255>}*1 {value22 <0-255>}*1 {value23 <0-255>}*1 {value24 <0-255>}*1 {value25 <0-255>}*1 {value26 <0-255>}*1 {value27 <0-255>}*1 {value28 <0-255>}*1 {value29 <0-255>}*1 {value30 <0-255>}*1 {value31 <0-255>}*1 {value32 <0-255>}*1
3. clear
4. clear_save gpio
5. commit section [0|1]
6. control opticalgenerator [enable|disable] mode [prbs7|prbs15|prbs23|prbs31|alt]
7. debug cli_msg id
8. debug cli_msg send_buf
9. del port_vlan_service
10. delete onuhw version
11. exit
12. fandebug [enable|disable]
13. get image status
14. get nvram
15. get system status
16. get version info
17. get web [user|admin] username
18. help
19. i2c read
20. i2c write
21. list
22. mibreset
23. optdebug [enable|disable]
24. output redirect
25. printenv env_key FHSNOUI
26. printenv env_key ethaddr
27. quit
28. read gpio <0-256>
29. read i2c device page <0-255> addr <0-255>
30. run [local_config]
31. run [omci_tl]
32. set bar code [pcb|bosa]
33. set black_list
34. set debug_level
35. set default-printf-to [disable|console|telnet|all]
36. set dhcp_delivery [disable|enable]
37. set electricfan run temperature <0-100> stop temperature <0-100>
38. set nvram
39. set oam_print [rx|tx|stop]
40. set omci_status
41. set onuhw version
42. set opt power [enable|disable]
43. set opt rxpoweradjust1 min max offset
44. set opt rxpoweradjust2 min max offset
45. set optoutpower level <0-2>
46. set optoutpower offset
47. set optpoll [enable|disable]
48. set optrxpower offset
49. set ponrate_config_switch <0-1>
50. set port_all_isolation [disable|enable]
51. set port_attribute [L2|L3]
52. set port_igmp_state [0|1]
53. set port_isolation [disable|enable]
54. set port_vlan_service
55. set pppoe_delivery [disable|enable]
56. set print_num
57. set queue_protect [on|off]
58. set show_packets [rx|tx|rtx|stop]
59. set web [user|admin] username password
60. set web default [user|admin] username password
61. setbuttondebug [disable|enable|start]
62. setleddebug [disable|enable|on|off]
63. setlog [omci|none] [old|pkt|timer|conf|temp|info|none|warning]
64. setpmlog <0-1>
65. setusbdebug
66. shell
67. show [ponrate_config_switch]
68. show bar code [pcb|bosa]
69. show black_list
70. show catv rf
71. show debugversion
72. show electricfan work temperature
73. show history
74. show optoutpower level
75. show optoutpower offset
76. show optrxpower adjust
77. show port_info
78. show power supply
79. show print_num
80. show queue_info
81. tshell
82. updateenv ethaddr
83. updateenv fhsnoui
84. upload ftp any
85. write gpio <0-256> <0-1>
86. write i2c device page <0-255> addr <0-255> value <0-255>
87. write_save gpio

Posted in: